Wood strips are supplied by the operator to the truck of the milling tenoner. Supply of elements initiates the miller work cycle. The stack face is levelled, after which milling of the finger joint outline is carried out. The miller truck returns to its starting position with preliminarily processed elements and returns the stack to the rotating supply table, where it is rotated. The stack is once again supplied to the milling tenoner, where the other side of the stack is processed.
TECHNICAL AND OPERATIONAL DATA: | ||
Width of the input stack milling tenoner | mm | 600 |
Maximum glued element width | mm | 30 ÷ 155 |
Length of glued elements | mm | 170 ÷ 900 |
Glued element thickness | mm | 20 ÷ 70 |
Working air pressure | MPa | 0,6 |
Demand for compressed air | m/h | 18 |
Operating output | cycles./min. | 1,5 |
Glued element length | mm | 4500 ÷ 6000 |
Working voltage | V AC | 3/N/PE 400 V 50 Hz |
Control voltage | V DC | 24 |
Electrical demand | kW | apprx. 52 |
OPERATION DESCRIPTION
Wood strips are supplied by the operator to the truck of the milling tenoner. Supply of elements initiates the miller work cycle. The stack face is levelled, after which milling of the finger joint outline is carried out. The miller truck returns to its starting position with preliminarily processed elements and returns the stack to the rotating supply table, where it is rotated. The stack is once again supplied to the milling tenoner, where the other side of the stack is processed.
Elements supplied from the DFC - 60 M tenoner through the chain conveyor are introduced to the preliminary tenoning unit, where preliminary clamping of the wedge-joints of square-sawn timber is carried out by means of a set of cylinders and a pressure pad before its introduction into the press.
The preliminarily tenoned square-sawn timber is directed to the press table, on which it is cut after achieving the required length. Next, the wood is transported into the area of the pressing bed by means of a pushing strip and pressure strip, where the pressing process takes place. Glued and pressed, the ready strip is pushed onto the receiving table of the press.
After square-sawn timber is moved into the area of the pressing bed, the process of element supply onto the press table is carried out in parallel. This maintains continuous press operation and also makes it possible to improve the efficiency of glue spreading.
TECHNICAL PARAMETERS OF THE DFC - 60M MILLER TENONER
Dimensions of the input raw material | ||
Length of input elements | mm | 170 ÷ 900 |
Milling height | mm | 20 ÷ 155 |
Width of the stack of processed elements | mm | 600 |
Possibility of milling with tools with a tooth length of | mm | 10 (5, 15, 20 optionally) |
Work cycle | automatic with manual material supply | ||
Working air pressure | MPa | 0,6 | |
Demand for compressed air | m3/h | apprx. 6 | |
Output of the extraction installation | m3/h | apprx. 4000 | |
Efficiency | cycles./min | apprx. 1,5 | |
Truck advance rate | m/min | operating | 10-23 |
return | 32 | ||
Working voltage | V AC | 3x400 + N + PE | |
Sampling Freq. | Hz | 50 | |
Control voltage | V DC | 24 | |
Start-up system of milling cutter drives | SOFTSTART | ||
Spindle rotational speed control | rpm | 6000 ÷ 4500 | |
Protection against drop in air pressure | MPa | below 0,45 |
TECHNICAL PARAMETERS OF THE PHSL PRESS
TECHNICAL AND OPERATIONAL DATA: | ||
Working supply height | mm | 890 ÷ 910 |
Maximum glued element width | mm | 35 ÷ 155 |
Glued element thickness | mm | 20 ÷ 70 |
Length of glued element min./max. | mm | 4500 ÷ 6600 |
Working air pressure | MPa | 0,6 |
Demand for compressed air | m3/h | 12 |
Output of the extraction installation | m3/h | 2000 |
Output of the two-track line - single milling tenoner | cycles/min. | apprx. 2 |
Working voltage | V AC | 3 x 400 + N + PE |
Sampling Freq. | Hz | 50 |
Control voltage | V DC | 24 |
Machine dimensions: | ||
Working height | mm | 900 ÷ 920 |
Total height | mm | 1475 |
Dimensions of the feeding and receiving table: | ||
Working height | mm | 900 ÷ 920 |
Total height | mm | 1060 |
Length | mm | 1100 |
width | mm | 678 |
Receiving table dimensions: | ||
Working height | mm | 900 ÷ 920 |
Total height | mm | 1060 |
Length | mm | 2000 |
width | mm | 732 |
Installed power | ||
DFC-60M milling tenoner | ||
tenoner saw and milling cutter | kW | 6 |
truck belt conveyor flight | kW | 0,55 |
truck drive | kW | 2,2 |
spindle drive | kW | 18,5 |
undercutting saw drive | kW | 1,1 |
pushing unit roller drive | kW | 0,37 |
arm pusher drive | kW | 0,75 |
receiving belt drive | kW | 1,1 |
PTLL Conveyor | ||
PTLL conveyor drive (chain) | kW | 2x1,5 |
PHSL Finger jointing press | ||
cross-cut saw motor | kW | 3,5 |
ZHE Hydraulic unit | ||
ZWCz drive pump | kW | 4,0 |
hydraulic actuator pump | kW | 3,0 |
Total | kW | 44,5 |
Optionally (on special order) - a system enabling the performance of one intercut
Possibility for performing intercuts of a preliminarily tenoned strip
- number of segments possible to be programmed - 8
- measuring accuracy approx. 10 mm on a single segment (dependent on the amount and length of tenoned elements)
Total